I WOULD LIKE DPF OFF FOR
BMW F10 520D
ECU : 0281016846
THNKS IN ADVANCE
BMW F10 520D
ECU : 0281016846
THNKS IN ADVANCE
↧
BMW F10 520D DPF OFF
↧
Hello
Hello I'm just joining to this site.
↧
↧
VOLVO 2.0D SID803 EGR OFF
Hello friends,
can somebody help with EGR OFF on VOLVO S60 2.0D 100kW 2006 SID803? I need 100% solution.
I attach BDM micro file.
Thank you for your help :)
regards
can somebody help with EGR OFF on VOLVO S60 2.0D 100kW 2006 SID803? I need 100% solution.
I attach BDM micro file.
Thank you for your help :)
regards
↧
Hello
Hello everyone, Charles here from Malaysia, nice to meet you all.
↧
Hello
Just a quick hello to the forum guys
↧
↧
Hello
Hello i am new User
↧
cd30 and display, need complet dumps
Hi guys
I need paired set dumps, to cd30 and display.
I need paired set dumps, to cd30 and display.
↧
Toyota hilux crash data
Hello Guys,
I have toyota hilux 2015 with crash data,Ecu 89170-0k141, can any one give me reset crash data,Thanks in advance.
I have toyota hilux 2015 with crash data,Ecu 89170-0k141, can any one give me reset crash data,Thanks in advance.
↧
64kb cutter
One more small utility from me.
This time i made utility which intended to divide full flash to code flash and data flash and for to glue together data flash and code flash
The program depends on net framework 4.6.1
1.To divide file size mast be between 323584 and 585728 bytes
2.To glue[COLOR=#8E8E8E] f
This time i made utility which intended to divide full flash to code flash and data flash and for to glue together data flash and code flash
The program depends on net framework 4.6.1
1.To divide file size mast be between 323584 and 585728 bytes
2.To glue[COLOR=#8E8E8E] f
↧
↧
DCM3.5 Citroen C5 need to Virgine
I have C5 with Delphi DCM3.5
HW 9666912580
DDS CMM DW10C CEM0
9667982380
I need to made ECU Virgine.
I read ALL post but in some case virginized only by eeprom 95640, in other case need to make MPC ( flash) also.
I post Flash and Eeprom File.
Anyone can help me?
Thanks!
HW 9666912580
DDS CMM DW10C CEM0
9667982380
I need to made ECU Virgine.
I read ALL post but in some case virginized only by eeprom 95640, in other case need to make MPC ( flash) also.
I post Flash and Eeprom File.
Anyone can help me?
Thanks!
↧
hello
hello im new user
↧
pin ducato bcm
Hi pleas pin bcm ducato dump st95160
↧
Hello, friends!
I will always be grateful to communicate with you!
↧
↧
Fiat palio immo off
Hi can anyone help me with a immo off file for a fiat palio. Please!!Image may be NSFW.
Clik here to view.![]()
Sent from my SM-G930F using Tapatalk
Clik here to view.
Sent from my SM-G930F using Tapatalk
↧
HELLO FRİENDS
I will always be grateful to communicate with you!
↧
Mercedes S320 W220 EZS(EIS) Problem
Vehicle has a problem with EIS, sometimes engine want start and sometimes engine starts but gearbox refuse to choose gear because of problems with ESP.
Before engine starts and on display shows ESP problem I can choose gear and drive but nothing on car is working, direction indicators, windshield wipers etc.
Car has a few errors:
P2201-001 CAN message from control module DAS: CAN signal faulty
P
Before engine starts and on display shows ESP problem I can choose gear and drive but nothing on car is working, direction indicators, windshield wipers etc.
Car has a few errors:
P2201-001 CAN message from control module DAS: CAN signal faulty
P
↧
HELLO
I will always be grateful to communicate with you!:peaceful::peaceful:
↧
↧
Hello everybody!!
I wish you all a good day.
↧
w164 vs w211 gateway
Please advice. Need cqw for bench setup. Can i use w211 gateway instead of w164?
Because prices 5 times differ for used cgw.
Because prices 5 times differ for used cgw.
↧
How to read EDC15C2 3 plugs Peugeot 307 HDI - Boot mode Galetto V54
Hi guys
I try to read the dump of a flash ECU EDC15C2 with Galletto V54 in pinout and boot mode but I can't. Should I connect the Galletto ground (black wire) (with or without the resistor 5Kohms) to flash PIN 24 or Galletto's gray wire (boot) for the boot mode. I want to make an immo off on the Flash 29F400BT.
I need your help !
Thanks in advance,
I try to read the dump of a flash ECU EDC15C2 with Galletto V54 in pinout and boot mode but I can't. Should I connect the Galletto ground (black wire) (with or without the resistor 5Kohms) to flash PIN 24 or Galletto's gray wire (boot) for the boot mode. I want to make an immo off on the Flash 29F400BT.
I need your help !
Thanks in advance,
↧